|
<-Back to How To Instruction
page
FAQ: Instructions on the application of screwback Spikes
All of the screwback spikes sold are made for easy application and great looks.
The screw supplied is used to fasten the spike onto your project. It is a quick
job to spike leather (or other material). Below is a detail description of each
step.
Detailed Instructions
- StudsAndSpikes sells "screwback" spikes because of their ease in small craft
projects or large productions, without needing any special dies or tools for
each spike. All of the spikes on StudsAndSpikes.com are sold with a screw
that fits the bottom tap of the spike.
- With the material you want to spike, punch a hole where you want the spike
to go. StudsAndSpikes sells a "Multi-Hole Punch" used for leather and similar
material.
2a) Tip: Often when working with certain denim or other
textiles, you may not want to "punch" out part of the material, as it may
fray. Instead you may want to spread the weave to make a hole big enough for
a screw. A non-bladed awl (Like our "Dart Awl") can help you with this.
- Take the screw and push it through the material so that the screw-head is
on the bottom of the material, and the threaded side points up. The hole should
fit the screw-thread snug; the screw should not be able to move around freely.
- Take the spike and twist/screw it onto the thread. To tighten it, use a
screwdriver on the bottom and twist while holding or pinching the spike as
hard as you can.
4a) Tip: When working with thin leather, denim or other
textiles, your material may be very thin. This may cause puckering material
or a sagging spike. You can try to use a backing to help keep the spike upright
to the material. Backings can include a small piece of leather, more cloth,
a washer, etc.
- Repeat steps for each spike. With practice and the right tools, your job
becomes quick and the finished product admirable.
Tools sold at StudsAndSpikes.com that may help apply spikes:
Multi-Hole Punch. (Item code: 170-0005)
This tool works well with leather and other tough materials. It comes with six
different punch sizes.
Dart Awl. (Item code: 170-0006)
A non-bladed awl, The Dart Awl has only one point for puncturing. A simple tool
that make small slits in leather or helps open holes in weave. This tool is
universal.
Cobblers Mat. (Item Code: 170-0003)
Sometimes it is used to protect the surface you are working on. The mat will
take the punches and slices when working with leather.
Mallet. (Item Code: 170-0004)
Sometimes used to help punch the awl through particularly thick or stubborn
leather.
Other low-cost household items and tools that may be used:
Exacto Knife.
May be used like the Awl to make slits. Watch out for their big blade; It is
bad if you make a slit in the material that is too wide for the screw.
Flathead Screwdriver, Phillips Screwdriver.
All of the spikes that StudsAndSpikes sells either have a flathead slot or a
Phillips slot. The screwdriver helps you tighten the spike onto the material.
Kitchen Cutting Board, Wood Board.
May be used to protect your work area from the blades or points of the awl.
When working with leather, wood often does not give as nicely as a Cobblers
Mat.
Loctite or Glue.
Loctite or other glues designed for metal can be used for extra hold or to attach.
When it is desirable for the screw to hold on tight to the spike, Loctite (or
similar metal glue) can be used. Many people using spikes for auto or motorbike
detailing will use Loctite Blue (or red for permanent glue) to secure the spike
onto the screw thread. (There are also other glues and epoxies used to secure
the spike right onto leather, plastic or other material without using the screw
for this, but this is not our expertise.)
<-Back to How To Instruction
page
|
